Company
Service
Media library
News
Careers
Contact
KAISER GROUP
Go back
Efficient installation and increased reliability thanks to innovative two-part design.
- The conduit entries are secured against accidental opening due to impacts from reinforcement steel or kicks - Open conduit entries are easily identified during inspections thanks to the junction box’s two colours - Horizontal and vertical slits in the sealing membrane enable the marking cross on the formwork to be seen through the membrane - Two-part design
Open Cadenas Modal
  • The conduit entries are secured against accidental opening due to impacts from reinforcement steel or kicks
  • Open conduit entries are easily identified during inspections thanks to the junction box’s two colours
  • Horizontal and vertical slits in the sealing membrane enable the marking cross on the formwork to be seen through the membrane
  • Two-part design
Read more Read less

Flush-mounted junction box - 115mm - for flexible corrugated plastic conduits (KRFG) with transformer tunnel

AGRO AG
Artikel-No.: 9907.30
E-No: 155011298
EAN: 7611614482217
SZ
CE
Product length: 380 mm
Product width: 115 mm
Product depth: 115 mm
For conduit Ø: 20 mm, 40 mm
Installation opening (for devices) length: 230 mm
Installation opening (for devices) width: 50 mm
Shipping: 5
More product details
Datasheet (PDF)

accessories

- Conforms to EN 60670-1 - UV-resistant
Push-on cover with diagonal support option, RAL 9010
Artikel-No. 9909.22
E-No 155910028
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Push-on cover with diagonal support option, RAL 7047
Artikel-No. 9909.22.65
E-No 155910138
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Push-on cover with diagonal support option, RAL 7012
Artikel-No. 9909.22.67
E-No 155910148
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Push-on cover with diagonal support option, RAL 9005
Artikel-No. 9909.22.60
E-No 155910158
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - With two isolated and tested centre screws (L=40/70 mm) - UV-resistant
Push-on cover with diagonal support option, RAL 9010
Artikel-No. 9909.10
E-No 155910808
  • Conforms to EN 60670-1
  • With two isolated and tested centre screws (L=40/70 mm)
  • UV-resistant
See more
- Conforms to EN 60670-1 - With two isolated and tested centre screws (L=40/70 mm) - UV-resistant
Push-on cover with central fixing, RAL 9010
Artikel-No. 9909.20
E-No 155910018
  • Conforms to EN 60670-1
  • With two isolated and tested centre screws (L=40/70 mm)
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Push-on cover with corner fixing, RAL 9010
Artikel-No. 9909.12
E-No 155910408
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Screwed-on cover with plastic screws, RAL 9010
Artikel-No. 9909.02
E-No 155910308
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Screwed-on cover with metal screws, RAL 9010
Artikel-No. 9909.05
E-No 155910508
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Cover with socket (Swiss type 13), RAL 9010
Artikel-No. 9909.02.13
E-No 155990108
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Cover with socket (Swiss type 15), RAL 9010
Artikel-No. 9909.02.15
E-No 155990208
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Cover with socket (Swiss type 23), RAL 9010
Artikel-No. 9909.02.23
E-No 155990408
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Cover with socket (Swiss type 25), RAL 9010
Artikel-No. 9909.02.25
E-No 155990508
  • Conforms to EN 60670-1
  • UV-resistant
See more
- with full neoprene seal - Cover fixing with enclosed screws, non-rusting
Waterproof cover
Artikel-No. 9909.03
E-No 155900098
  • with full neoprene seal
  • Cover fixing with enclosed screws, non-rusting
See more
- For increasing the front-to-back depth of the box or for sub-ceiling insulation - Multiple extensions possible - With two fixing screws
Extension piece - 12mm - for junction box 9907 / 9907.21
Artikel-No. 9907.68
E-No 155992198
  • For increasing the front-to-back depth of the box or for sub-ceiling insulation
  • Multiple extensions possible
  • With two fixing screws
See more
- For increasing the front-to-back depth of the box or for sub-ceiling insulation - Multiple extensions possible - With two fixing screws
Extension piece - 45mm - for flush-mounted junction box 9907 / 9907.21
Artikel-No. 9907.68.45
E-No 155992298
  • For increasing the front-to-back depth of the box or for sub-ceiling insulation
  • Multiple extensions possible
  • With two fixing screws
See more
- Facilitates fixing to the reinforcement - For wire-pull casings (Art. No. 9907.10 and 9907.10.21) - For wire-pull casings (Art. No. 9916 and 9917)
Set of 2 Prefix® wing brackets
Artikel-No. 9940.20
E-No 155901308
  • Facilitates fixing to the reinforcement
  • For wire-pull casings (Art. No. 9907.10 and 9907.10.21)
  • For wire-pull casings (Art. No. 9916 and 9917)
See more
DIAGONAL SUPPORT
DIAGONAL SUPPORT
Artikel-No. 9907.60
E-No 155910128
See more

Efficient installation and increased reliability thanks to innovative two-part design.

Our latest version of this product (Art.-No. 9907.30) also includes an integrated tunnel extension, supporting the trend towards efficient LED strip lighting in residential installations. This product offers all the benefits of the already successful 9907.20 series. The specially designed tunnel extension can accommodate LED strip lighting drivers up to a size of 230 x 50 x 35 mm. Especially in areas such as showers, bathrooms or corridors where LED lighting plays an important role, the flush-mounted junction box with tunnel extension offers an ideal solution. It enables electrical designers to easily incorporate LED strip lighting into their plans, as this item is specially designed for this purpose. It provides flexibility during the installation work on site while helping to ensure safety and reliability.

Processing instructions

Align and fix the front part to the formwork using the four pre-installed nails.
Align and fix the front part to the formwork using the four pre-installed nails.
Snap the top part of the junction box onto the front part.
Snap the top part of the junction box onto the front part.
Open the required conduit entries with a hammer.
Open the required conduit entries with a hammer.
Connect conduits to the junction box and secure them with cable ties.
Connect conduits to the junction box and secure them with cable ties.
Connect conduits to the junction box and secure them with cable ties.
Connect conduits to the junction box and secure them with cable ties.
For secure installation in wall formwork, use Prefix® wing brackets, set of two (Art.-No. 9940.20).
For secure installation in wall formwork, use Prefix® wing brackets, set of two (Art.-No. 9940.20).
When installed in wall formwork, transformer tunnels must be aligned downwards.
When installed in wall formwork, transformer tunnels must be aligned downwards.
After stripping the formwork, open the diaphragm with a hammer and, if necessary, a screwdriver.
After stripping the formwork, open the diaphragm with a hammer and, if necessary, a screwdriver.
Wire the driver and push it into the transformer tunnel.
Wire the driver and push it into the transformer tunnel.
In the case of insulated slabs, extension pieces (Art.-No. 9907.68 and 9907.68.45) may be used (several if required).
In the case of insulated slabs, extension pieces (Art.-No. 9907.68 and 9907.68.45) may be used (several if required).
Various covers in different colours are available for an attractive appearance.
Various covers in different colours are available for an attractive appearance.

Dimensions / Form

Product length:
380 mm
Product width:
115 mm
Product depth:
115 mm
Installation opening (for devices) length:
230 mm
Installation opening (for devices) width:
50 mm

Connections / Entries

For conduit Ø:
20 mm, 40 mm

Assembly / Installation

Assembly type:
BB (solid construction)

Safety / Properties

Special application:
on-site mixed concrete
Certificate

9907.30 Flush-mounted junction box for flexible corrugated plastic conduits (KRFG)

2.9 MB | 16/01/2025
Download
Innovative flush-mounted junction boxes with integrated tunnel extensions for concrete installations
Flyer

Innovative flush-mounted junction boxes with integrated tunnel extensions for concrete installations

1.1 MB
- Conforms to EN 60670-1 - UV-resistant
Push-on cover with diagonal support option, RAL 9010
Artikel-No. 9909.22
E-No 155910028
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Push-on cover with diagonal support option, RAL 7047
Artikel-No. 9909.22.65
E-No 155910138
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Push-on cover with diagonal support option, RAL 7012
Artikel-No. 9909.22.67
E-No 155910148
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Push-on cover with diagonal support option, RAL 9005
Artikel-No. 9909.22.60
E-No 155910158
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - With two isolated and tested centre screws (L=40/70 mm) - UV-resistant
Push-on cover with diagonal support option, RAL 9010
Artikel-No. 9909.10
E-No 155910808
  • Conforms to EN 60670-1
  • With two isolated and tested centre screws (L=40/70 mm)
  • UV-resistant
See more
- Conforms to EN 60670-1 - With two isolated and tested centre screws (L=40/70 mm) - UV-resistant
Push-on cover with central fixing, RAL 9010
Artikel-No. 9909.20
E-No 155910018
  • Conforms to EN 60670-1
  • With two isolated and tested centre screws (L=40/70 mm)
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Push-on cover with corner fixing, RAL 9010
Artikel-No. 9909.12
E-No 155910408
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Screwed-on cover with plastic screws, RAL 9010
Artikel-No. 9909.02
E-No 155910308
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Screwed-on cover with metal screws, RAL 9010
Artikel-No. 9909.05
E-No 155910508
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Cover with socket (Swiss type 13), RAL 9010
Artikel-No. 9909.02.13
E-No 155990108
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Cover with socket (Swiss type 15), RAL 9010
Artikel-No. 9909.02.15
E-No 155990208
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Cover with socket (Swiss type 23), RAL 9010
Artikel-No. 9909.02.23
E-No 155990408
  • Conforms to EN 60670-1
  • UV-resistant
See more
- Conforms to EN 60670-1 - UV-resistant
Cover with socket (Swiss type 25), RAL 9010
Artikel-No. 9909.02.25
E-No 155990508
  • Conforms to EN 60670-1
  • UV-resistant
See more
- with full neoprene seal - Cover fixing with enclosed screws, non-rusting
Waterproof cover
Artikel-No. 9909.03
E-No 155900098
  • with full neoprene seal
  • Cover fixing with enclosed screws, non-rusting
See more
- For increasing the front-to-back depth of the box or for sub-ceiling insulation - Multiple extensions possible - With two fixing screws
Extension piece - 12mm - for junction box 9907 / 9907.21
Artikel-No. 9907.68
E-No 155992198
  • For increasing the front-to-back depth of the box or for sub-ceiling insulation
  • Multiple extensions possible
  • With two fixing screws
See more
- For increasing the front-to-back depth of the box or for sub-ceiling insulation - Multiple extensions possible - With two fixing screws
Extension piece - 45mm - for flush-mounted junction box 9907 / 9907.21
Artikel-No. 9907.68.45
E-No 155992298
  • For increasing the front-to-back depth of the box or for sub-ceiling insulation
  • Multiple extensions possible
  • With two fixing screws
See more
- Facilitates fixing to the reinforcement - For wire-pull casings (Art. No. 9907.10 and 9907.10.21) - For wire-pull casings (Art. No. 9916 and 9917)
Set of 2 Prefix® wing brackets
Artikel-No. 9940.20
E-No 155901308
  • Facilitates fixing to the reinforcement
  • For wire-pull casings (Art. No. 9907.10 and 9907.10.21)
  • For wire-pull casings (Art. No. 9916 and 9917)
See more
DIAGONAL SUPPORT
DIAGONAL SUPPORT
Artikel-No. 9907.60
E-No 155910128
See more
PARTcommunity

PARTcommunity

Planning Data (CAD/3D/2D)