The Consolidation Box from Attema makes it possible to install ICT cabling in a flexible manner, because the installation is divided into two steps. The largest portion of the work takes place during the rough construction, at the same time as the other cabling is installed in the building. As a result, you only have to install a small portion of the ICT cabling during the finishing phase. The Consolidation Box complies with the installation standards of EIA/TIA 568A/B, ISO 11801 and NEN-EN 50173.
Consolidation Box
AK2 Data basic housing with flat mounting plate
Product length:
120 mm
Product width:
95 mm
Product depth:
40 mm
Number of entries:
10
Fastening type (other):
Shallow mounting plate
Halogen-free:
Yes
Packaging quantity:
10
accessories
AK2-S Flat mounting plate
Article number:
AT2249
- Flat plastic mounting plate for quick click-mounting on cable trays.
- Suitable for cable trays from Legrand (Van Geel), Stago, Niedax, Vergokan, PUK and OBO.
- To be used in combination with AK2-S underbody.
- Particularly intended for the self-assembly of a 'twisted' AK2-S underbody on the mounting plate for mounting on the back of a cable tray
- Suitable for cable support systems from well-known manufacturers
Data cable entry
Article number:
AT1966
- The slide-in data lead-in, made of soft rubber, is suitable for the lead-in of a maximum of 3 data cables (UTP, FTP, STP etc.).
- Provides grip on the cable sheath without untwisting the conductor pairs or in any other way influencing the data transmission.
- for AK2 housing
Blanking plug
Article number:
AT2257
- Provides closure of lead-ins on AK2-S junction boxes that have been broken out but will not be used.
- Can be punctured to allow lead-in of thin cables < Ø 10 mm.
- for AK2 housing
Consolidation Box
ETIM Product Classification:
Box/housing for surface mounting on the wall/ceiling
Box/housing for surface mounting on the wall/ceiling
Model:
Junction box
Equipped with:
Mounting plate
Max. conductor cross section:
Number of poles:
Number of clamp positions per pole:
Shape:
Rectangular
Mounting method:
On cable tray
Mounting in the soil:
No
Mounting under water:
No
Suitable for tube diameter:
Number of inlets:
10
Inlet from the rear:
No
Length:
120 mm
Width:
95 mm
Depth:
40 mm
Diameter:
Number of cable glands included:
Connectable:
No
Type of housing feed-through:
Preembossing
With strain relief:
Material:
Plastic
Halogen free:
No
Surface protection:
Untreated
Colour:
Grey
RAL-number (similar):
Degree of protection (IP):
IP20
Degree of protection (NEMA):
Cover model:
None
Outgoing connections with connectors for plug-in building installation:
Transparent cover:
No
Castable:
No
Cover attachment:
Snapped on
Casting compound included:
No
Sealable:
No
Rated insulation voltage Ui:
690 V
Circuit integrity:
None
With screening:
No
Weatherproof:
No
Working temperature:
-40 - 70 °C
Explosion-tested version:
No
Suitable for Ex-zone gas:
None
Suitable for Ex-zone dust:
None
Dimensions / Form
- Product length:
- 120 mm
- Product width:
- 95 mm
- Product depth:
- 40 mm
Connections / Entries
- Number of entries:
- 10
Installationdetails
- Fastening type (other):
- Shallow mounting plate
Safety / Properties
- Halogen-free:
- Yes
Certificates & Quality marks
- VDE:
- Yes
Storage / Installation / Operation
- Minimum operating temperature:
- -40 °C
- Maximum operating temperature:
- 70 °C
AK2-S Flat mounting plate
Article number:
AT2249
- Flat plastic mounting plate for quick click-mounting on cable trays.
- Suitable for cable trays from Legrand (Van Geel), Stago, Niedax, Vergokan, PUK and OBO.
- To be used in combination with AK2-S underbody.
- Particularly intended for the self-assembly of a 'twisted' AK2-S underbody on the mounting plate for mounting on the back of a cable tray
- Suitable for cable support systems from well-known manufacturers
Data cable entry
Article number:
AT1966
- The slide-in data lead-in, made of soft rubber, is suitable for the lead-in of a maximum of 3 data cables (UTP, FTP, STP etc.).
- Provides grip on the cable sheath without untwisting the conductor pairs or in any other way influencing the data transmission.
- for AK2 housing
Blanking plug
Article number:
AT2257
- Provides closure of lead-ins on AK2-S junction boxes that have been broken out but will not be used.
- Can be punctured to allow lead-in of thin cables < Ø 10 mm.
- for AK2 housing